If this is your first visit to this site, please read the help. There you will be able to operate the site in more detail. The regular M203 grenade launcher is attached to the hand guard holder and the barrel. This model will, however, bolted from the bottom on a RAS / RIS rail that is attached to the hand guard, or by the hand of protection has been replaced. This has the advantage that you build it faster and can and can fix any other things on the hand guard. However, it is thus not quite as firmly fitted (but as the airsoft not such a big role as the sharp model). The M203 is available in three different lengths that work but basically all the same. In this review, the longest version is presented. The complete grenade launcher is made of metal, only the "shaft", which is attached to the tube, in which the grenade is ignited, is made of a very qualitative plastic. (To be honest, I thought at first this would also touch of metal, and despite thorough investigation.). There are also the Importeurmarkings (sniper) and the and "Einlegepatrone" eingestänzt or milled. Unfortunately, these are the only places where mortars are not black. (The picture only vaguely recognizable.). Above the barrel, a three millimeter thick sheet is attached as an opening mechanism. If you press them, you can run the slide forward to load a grenade. My grenade launcher was a set from the M203 and a comprehensive 18 BBs grenade. I'm not here on a shot to the behavior, because this is determined mainly by the grenade, and my best is certainly not. As you can imagine already, slide the grenade (as soon as it is loaded) into the barrel and pulls back the barrel to the lock / action frame (actually something like a shotgun) Is. There was however a problem in the first days. I had to pretty much every time fiddle for a few seconds because the course did not want to engage in the lock. I have almost taken a week to find out that they close down the barrel at the left must move so that it snaps into place right at the first attempt. I can not say whether this is a general problem or unique to my model. I'll handle it very well but mitlerweile. Before invites his grenade, one should secure the trigger. To trigger a second before the actual trigger is appropriate. This to ensure you have to pull the trigger point. If you want to shoot then you can push the bar with the trigger finger forward and thus the trigger again to release. The run, which is on the Airsoft replica actually garkein run was, from the inside provided with a few trains, hereinstehen inside. I would imagine that this was done so that you can not front load as well or even comes up with the idea to use up a live shell (even though I is not clear how to get to one). Attached to the grenade launcher is as already described in a RIS / RAS hand guard rail. Previously, one should pinch the trigger guard on the magazine well. I have attached my grenade launcher in this image from a RAM 3R. (For 1R is a small depression on the course, so you could put there, even a grenade launcher attachment with others. These absent in 3R, however, so I went for a RAS / RIS installation.).

Dboys M203 Airsoft Grenade Launcher Long 3 in 1 - Black BIM203L was bookmarked by from ,

Colt M203 Grenade launcher Model 4 Series was bought by from ,

Dboy Airsoft Grenade 24 Round BB Shower 40mm for M203 Launchers was bookmarked by from ,

Dboys M203 Airsoft Grenade Launcher Short 3 in 1 - Black BIM203 was bookmarked by from ,

Dboys M203 Airsoft Grenade Launcher Short 3 in 1 - Black BIM203 was rated 6 by from ,

Echo1 2-in-1 M203 Airsoft Grenade Launcher - Long was recommended by from ,

M4 3181 AEG Electric Airsoft Rifle, M203 Grenade Launcher, 2 Stocks, FPS-300, Extra Mag was recommended by from ,

Colt M203 Grenade launcher Model 4 Series was bought by from ,

M4 3181 AEG Electric Airsoft Rifle, M203 Grenade Launcher, 2 Stocks, FPS-300, Extra Mag was recommended by from ,