The replica is a strong investment, and it is important to review it to work correctly without compromising performance. Before making any revisions to the reply do not forget to remove the magazine, empty the shots that may be within it (shoot some times there are no balls in the feeder or in the inner chamber), and remove the battery or gas. First start with cleaning, and try not to scratch the surface. Use soft paper or cloth and a mixture of soap and water. Mechanism removes any dirt or canyon. After cleaning you should lubricate the reply, and you use only Airsoft Silicone lubricants such as silicone spray or silicone grease and oil lubricants that destroy the rubber seals and the like. The lubricating oil may also destroy the surface of some replicas. The maintenance of these mirrors is very simple because they are of simple construction. The only problems are serious and mechanisms cylinders damaged or worn. A cannon is often obstructed ball low quality and improved guns. A dirty gun tube will cause a decrease in performance. The basic routine to keep your mirrors in good condition are as follows: if the replica can be removed, desmóntala and clean of dust and particles before lubricating the parts. Use a spray bottle to apply a thin layer of lubricant on the parts that slide against each other, and do not forget to lubricate the hopup and the rubber ring that holds the ball to keep dry. Clean the charger, but do not lubricate (and lube little), so that the balls are not sticky and has traffic jams. After oiling removes excess lubricant with a soft exterior. The hopup work a little shaky until the excess lubricant is removed. These replicas are a little more difficult to maintain, though its construction is simple. Just few taps are needed to maintain gas replica in good condition. Basically, all replicas have a gas valve, either the shipper or the replica itself. To maintain the valves in good condition, use a screw driver (the appropriate size) and carefully remove the valve. Put a few drops of thin silicone oil in the gas tank, and replace the valve with care. Do not tighten the valve very strong, just let it sit. Gas is mixed with silicone oil, which this operation can be avoided. The blowback replicas are among the most hostile when it comes to maintenance, with the exception of a gearbox AEG. But the basic principle is the same as for other replicas, and with the help of common sense and a bit of information anyone can review a blowback. For all I know, all replicas of blowback are removed in some way. You need the manual to dismantle and assemble correctly. Here are some tips. First lubricates the gas tank as explained above, and then removing the gun blowback locates the board, which must be at the top, below the rear sight. Lubricate the rubber ring. Do not stretch very strong pieces, because some may be engaged with a spring, and do not want this spring to fall. Clean and lubricate sliding surfaces at the top and bottom. Only you will be riding the gun again and the review is complete.Use the tool that comes with the gun to clean the barrel. One end of the bar is milled, and is used to remove ball stuck in the barrel. If a ball is stuck in the barrel, put the safe to remove the charger. Gently inserts the bar with the beveled side facing inwards. All balls must fall by the stuck ball feeder. The other end of the bar has a rectangular shape with a hole. Use a rectangular piece of clothing or soft paper, put it through the hole and gently roll it around the bar. Lubricate the cloth with a few drops of oil and gently push the bar down the barrel until it reaches the red marks (before reaching the hopup). Take the bar, replace the cloth and repeat the process until the cloth is clean. This cleaning process should be done every 2000 shots, but if the weapon has been used in a very dirty game, the gun should be cleaned later. A clean gun is important for performance. Apart from this, the battery is the only thing that needs to be revised. Never overfill a battery, because it can "burn" and never burned a battery will behave properly. The battery should be charged not enough, because you may develop a memory effect and the capacity decrease. The battery should never be downloaded at all, and the discharge should stop when the voltage drops to 70% (6 V to 8.4 V battery). When the engine no longer has enough power to move the gear you charge the battery. Charge the battery in slow mode, to keep it in the best conditions. Fast charging is not good for the batteries and their life expectancy decreases. Do not upload faster than 15 minutes, and remember that a charged battery should be cooled quickly before use and will not have the same capacity as a battery load slowly. It is recommended to load fast for more than an hour, as it is a good compromise between charging time and battery condition. And the battery only a little more heated. Autoloaders are the best because they can not overcharge a battery. The AEG are the only mirrors that have the option to use high capacity magazines. These boots should be checked every 5000 shots or so, but as the magazine review age requirements increase. Just as with AEG, leaves a person experienced the review of HiCap. To avoid damage and increase the life of the magazine, try to keep away from dust, grease, leaves and pieces of broken beads. ..

9.6V 1600mAh NiMH Flat Battery Pack for Airsoft Gun was recommended by from ,

Heavy M4 M16 Replica Airsoft Gun Double Eagle M83 A2 Full Automatic Electric Rifle was added to shopping list by from ,

TSD Universal Smart Charger 7.2-12V for NiCad & NiMH batteries was bought by from ,

Heavy M4 M16 Replica Airsoft Gun Double Eagle M83 A2 Full Automatic Electric Rifle was added to shopping list by from ,

Heavy M4 M16 Replica Airsoft Gun Double Eagle M83 A2 Full Automatic Electric Rifle was bookmarked by from ,

8.4V 1600mAh NiMH Flat Battery Pack for Airsoft Guns was bought by from ,

8.4V 1600mAh NiMH Flat Battery Pack for Airsoft Guns was recommended by from ,

UTG AccuShot Airsoft Competition Auto-Reset Target was bought by from ,

1:1 FULL SCALE Spring Powered Scarface M16 with Grenade Launcher, LED Flashlight, Laser Aiming Sight, Foregrip, M16 FPS-260 Grenade Launcher FPS-300 M16 Airsoft Guns was bought by from ,